Ecological inference using data from accelerometers needs careful protocols

Abstract Accelerometers in animal‐attached tags are powerful tools in behavioural ecology, they can be used to determine behaviour and provide proxies for movement‐based energy expenditure. Researchers are collecting and archiving data across systems, seasons and device types. However, using data repositories to draw ecological inference requires a good understanding of the error introduced according to sensor type and position on the study animal and protocols for error assessment and minimisation. Using laboratory trials, we examine the absolute accuracy of tri‐axial accelerometers and determine how inaccuracies impact measurements of dynamic body acceleration (DBA), a proxy for energy expenditure, in human participants. We then examine how tag type and placement affect the acceleration signal in birds, using pigeons Columba livia flying in a wind tunnel, with tags mounted simultaneously in two positions, and back‐ and tail‐mounted tags deployed on wild kittiwakes Rissa tridactyla. Finally, we present a case study where two generations of tag were deployed using different attachment procedures on red‐tailed tropicbirds Phaethon rubricauda foraging in different seasons. Bench tests showed that individual acceleration axes required a two‐level correction to eliminate measurement error. This resulted in DBA differences of up to 5% between calibrated and uncalibrated tags for humans walking at a range of speeds. Device position was associated with greater variation in DBA, with upper and lower back‐mounted tags varying by 9% in pigeons, and tail‐ and back‐mounted tags varying by 13% in kittiwakes. The tropicbird study highlighted the difficulties of attributing changes in signal amplitude to a single factor when confounding influences tend to covary, as DBA varied by 25% between seasons. Accelerometer accuracy, tag placement and attachment critically affect the signal amplitude and thereby the ability of the system to detect biologically meaningful phenomena. We propose a simple method to calibrate accelerometers that can be executed under field conditions. This should be used prior to deployments and archived with resulting data. We also suggest a way that researchers can assess accuracy in previously collected data, and caution that variable tag placement and attachment can increase sensor noise and even generate trends that have no biological meaning.


| INTRODUC TI ON
Animal-attached tags have revolutionised our understanding of wild animal ecology (Bograd et al., 2010;Sequeira et al., 2021;Yoda, 2019). Of the sensors often used, accelerometers (Yoda et al., 1999) are regarded as a particularly powerful tool for studying wild animal behavioural ecology, with studies using them to look at the occurrence and intensity of behaviour (Chakravarty et al., 2019;Fehlmann et al., 2017), assess movement characteristics  and as a proxy for energy expenditure . The latter has developed rapidly since the demonstration that dynamic body acceleration (DBA) is related to energy expenditure across a range of vertebrates and invertebrates (Halsey et al., 2009;Wilson et al., 2006Wilson et al., , 2019. Such measurements have great potential for understanding animal strategies, in particular studying how animals respond to changes in food availability (Kokubun et al., 2011), climate (Gudka et al., 2019) and anthropogenic threats or activity (Nickel et al., 2021;Payne et al., 2015;Yorzinski et al., 2015).
In terrestrial mammals (cf. Field et al., 2011 for a comparison with marine mammals), accelerometers tend to be attached using collars, providing a largely standardised position of attachment, although collars have their own complications in terms of the need to obtain a good fit and account for collar rotation in data interpretation . In contrast, researchers use different attachment positions on birds. For instance, tags are deployed on the lower back, the tail or the belly of seabirds depending on the species and the tag position associated with least detriment (Elliott, 2016;Ropert-Coudert et al., 2003;Vandenabeele et al., 2014). Researchers working with raptors may deploy tags using backpack or leg-loop harnesses (e.g. Harel et al., 2017;Williams et al., 2015 respectively), which results in differences in tag position. The widespread availability and use of accelerometers mean that large datasets, collected over years, are now available, providing valuable information about behaviour, including flight effort across temporal and spatial scales (Kranstauber et al., 2011). Unsurprisingly, these data have been collected using different methods of attachment and by deploying a variety of different tags without critical analysis of the compatibility of different datasets (Sequeira et al., 2021).
Tag position on the body is likely to affect acceleration values, as pointed out by Wilson et al. (2020), who noted that DBA  varied with tag position in humans wearing back-and waist-mounted tags running on a treadmill (with DBA values varying by ~0.25 g at intermediate speeds). This is easy to understand since humans have a flexible spine. Birds, on the other hand, have an essentially immoveable box-like thorax (Baumel, 1993). Differences in acceleration between tags placed on the back and the neck (Kölzsch et al., 2016) or the tail (Elliott, 2016) are easy to associate with independent movement of the head or tail, but the thorax itself can experience pitch changes over the wingbeat cycle (Su et al., 2012;Tobalske & Dial, 1996), which may affect the acceleration recorded by loggers depending on their position. In line with this, we note that the precise position of the accelerometer chips on the circuit boards may also affect the acceleration measured by the sensors, particularly in cases where the circuit board is long relative to the bird's back and where the chip could be positioned close to either end.
At a more fundamental level, the fabrication of loggers with accelerometers involves extensive heating as the sensors are soldered to the circuit boards. Although the literature notes that there is a temperature-dependent output of accelerometers under normal operating conditions (this normally being corrected within the chip; e.g. Yin et al., 2019), the heating process changes the output versus acceleration in a fundamentally different manner (Ruzza et al., 2018), even if they are carefully calibrated prior to this process (see https:// www.mouser.co.uk/datas heet/2/389/dm001 03319 -17980 35.pdf).
Specifically, while the vector sum of the three acceleration channels should be 1 when a unit is at rest (Won & Golnaraghi, 2009), this can vary after heating, resulting in error in the estimation of the Earth's gravitational component. This can in turn introduce error difficulties of attributing changes in signal amplitude to a single factor when confounding influences tend to covary, as DBA varied by 25% between seasons. 4. Accelerometer accuracy, tag placement and attachment critically affect the signal amplitude and thereby the ability of the system to detect biologically meaningful phenomena. We propose a simple method to calibrate accelerometers that can be executed under field conditions. This should be used prior to deployments and archived with resulting data. We also suggest a way that researchers can assess accuracy in previously collected data, and caution that variable tag placement and attachment can increase sensor noise and even generate trends that have no biological meaning.

K E Y W O R D S
accelerometry, accuracy, biologger, biotelemetry, calibration, DBA, tag placement into the estimation of the 'dynamic' acceleration, or acceleration due to movement, which is the basis for acceleration-based proxies for energy expenditure . While the engineering literature discusses methods for identifying and correcting inaccuracies in accelerometer readings using rotational-tilt platforms or motion rate tables (or similar) and adopting calibration algorithms (Sipos et al., 2011), approaches such as Kalman filter covariance matrices (Beravs et al., 2012), dynamic filtering for bias issues (Batista et al., 2011) or iterative simulations for gain and bias compared to measured values (Won & Golnaraghi, 2009), the importance of this has not been highlighted in the biological literature (Cade et al., 2021).
In this manuscript, we assess the error associated with the sensors themselves and how the position and fixing of the accelerometer on the study animal affects acceleration metrics before proposing simple solutions to minimise these issues. Specifically, we examine the variability in VeDBA associated with improperly calibrated tri-axial accelerometers, using a case with humans walking defined courses at fixed speeds. We then examine how tag position affects VeDBA and signal amplitude using pigeons Columba livia flying in a wind tunnel with two tags in different locations on their back. Finally, we perform retrospective analyses of two field studies to examine how different deployment protocols may affect accelerometer-based results, in; (a) red-tailed tropicbirds Phaethon rubricauda equipped with two different types of loggers attached using marginally different protocols in separate seasons, and (b) black-legged kittiwakes Rissa tridactyla equipped with tags either on the back or on the tail, as two positions favoured by seabird researchers for tag placement. Finally, we examined publications from biologists using accelerometers over the last 2 years to determine how many of them had indicated an accelerometer calibration protocol.

| Measurement of acceleration accuracy of triaxial sensors
We first calibrated tri-axial accelerometers within five Daily Diary tags (inch board) (Wildbyte Technologies, Swansea University, UK; Wilson et al., 2008), by setting them motionless on a table in a series of defined orientations (each for c. 10 s). Six orientations (hereafter the '6-O method') were chosen so that the tags always had one of their three acceleration axes perpendicular to the Earth's surface and these were rotated according to the six axes of a die so that each of the three accelerometer axes nominally reads −1 and 1 g ( Figure 1a).
The outputs of these motionless calibrations were then used to derive the six respective maxima of the acceleration vectorial sum given by; where x, y and z are the raw acceleration values, for the periods when they were held still. Note that there are six maxima because each axis has two values: a minimum and a maximum, which become positive in the vectorial sum. In a device with perfect acceleration sensors, all maxima should be 1.0 g (Won & Golnaraghi, 2009) (although the acceleration on earth varies with latitude by up to a maximum of 0.0053 g due to the earth's shape and the centrifugal force generated by the planet spinning as well as other processes; Novák, 2010). However, values were always either marginally higher or lower than 1.0 g (see Section 3). Furthermore, the two maxima for each axis differed (e.g. Figure 1b). This therefore requires two steps to be corrected, where; (a) a correction factor is applied to the values in each axis to ensure both absolute 'maxima' per axis are the same and then (b) a gain is applied to both readings to convert them to be exactly 1.0 g. Thus, for each axis used, the following equation To ensure that only steady sustained level flight was included in the analysis, we selected sections of consistent flapping flight lasting for at least 2 s (corresponding to c. 10 wingbeat cycles), with no gliding or wingbeat interruptions. The stability of the flight was controlled by selecting sections where VeDBA values, smoothed over 1 s, were between 0.75 and 3 g and varied by <1.0 g, with no apparent trend (increasing or decreasing) over time. We also discarded the first second of any flight.
We first assessed whether the VeDBA values differed with tag position. VeDBA was calculated using a 2 s smoothing window to derive the 'static' component  and then subtracting static values from the raw acceleration data in each axis, before summing the differences vectorially .
We then assessed whether the peak amplitude per wingbeat differed according to tag location, with the peak amplitude calculated as the difference between the maximum and the minimum value of heave acceleration. For this, peaks were detected in the heave axis (Bishop et al., 2015) to synchronise every wingbeat to a defined start point. Finally, to understand which parts of the wingbeat signal were affected by the difference in tag position, we analysed the acceleration signals across average wingbeats in the three acceleration axes.
Each acceleration datapoint was attributed to a percentage progression across the wingbeat cycle. Then, for every whole percentage value, the heave, surge and sway accelerations were averaged across 10 wingbeats from the same logger. The average values for the heave, surge and sway accelerations of the upper back-mounted tag were expressed against the values of the lower back-mounted tag in a linear model, the slope of which was used to determine the difference in signal amplitude between the two tags for each acceleration axis.
To examine putative changes in heave signal amplitude (see above) and VeDBA associated with tag placement, we compared them between upper and lower back tags using a paired Student's t-test for VeDBA and a Wilcoxon signed-rank test for amplitude (due to non-homogeneous variances between the two groups [Levene's Test: F-value = 4.159, p = 0.049]). Wingbeat frequency also contributes to the variation of VeDBA (Van Walsum et al., 2020). Wingbeat frequency was also compared between the two tags using a paired F I G U R E 1 Simple, field viable six-orientation calibration procedure for helping correct for accelerometer offset and gain errors. (a) Shows the tag on a flat surface such as a table, with each of the six orientations uppermost (for periods of e.g. 5-10 s). (b) Shows the raw vectorial sum of the acceleration data of a typical tag rotated to adopt each of the six positions and (c) shows the same data after correction. In this case, the respective offsets and gains for the three axes were; Ax (offset −0.027 g, gain 1.023 g), Az (offset −0.018 g, gain 1.021 g) and Ay (offset 0.025 g, gain 1.000 g). Rotation of the tag at various angles led to pre-correction acceleration vectorial sums varying between 0.948 and 1.037 g. These reduced to between 0.996 and 1.007 g post-correction. Note how the correction process affects all acceleration data, including such times as when the tag is moving appreciably (such as during rotation) and has centripetal and/or linear acceleration values (manifest by the dips and peaks between flat tops) AcceleraƟon vectorial sum (g) AcceleraƟon vectorial sum (g) Student's t-test. The statistical analysis was performed in RStudio, using r version 4.0.3 (R Core Team, 2020). Nineteen birds were tagged between February and March 2018 (using type 2 DDs, Figure 2) while 36 birds were tagged during the second season (September and October 2018, type 1 DDs, Figure 2).

| Acceleration error in field studies
Importantly, during the second season though, the tags were attached using only three strips of tape. At the time, this was considered adequate and helped reduce the weight of the unit. Both units were set to the same sampling frequency (40 Hz). They were, however, built with different accelerometers (type 1: LSM9DS1, type 2: LSM303DLHC, STMicroelectronics, Geneva, Switzerland), with a substantial difference in sensitivity (type 1: 0.061 mg, type 2: 1.0 mg sensitivity at ±2 g range). In addition, the accelerometer is placed at the front of the type 1 unit, and at the back of the type 2 unit, leading to an estimated distance of up to 1 cm between them once placed on the bird's back. The type 1 tags used in the second season were slightly lighter (masses; type 1 unit = 25.0 g, type 2 unit = 27.7 g). As with the kittiwakes, level flapping flight was selected to discard the effect of gliding, thermal soaring or climbing on acceleration metrics (Williams et al., 2015). Since both the tropicbird and kittiwake data were collected from uncalibrated accelerometers (see above), a situation that we believe represents most of the accelerometer deployments made by the community to date, we attempted to assess the potential for accelerometer error post hoc. We did this by measuring the variability in the vectorial sum at times when the tags were motionless (although F I G U R E 2 (a) Location of the accelerometer (interception point of the three arrows depicting tri-axial acceleration) on the circuit boards of two different DD tags (the battery is in light grey, the GPS in blue and the DD in green) and (b) location of the accelerometers within the tags on the back of a red-tailed tropicbird for the type 1 (red dot) and type 2 (blue dot) tags not on the study animals) and in different tag orientations, finding up to five different orientations per logger (e.g. when units were placed inside bags and the bag placed on the floor/ground). The mean vectorial sum of the three axes of acceleration was calculated for each orientation, and compared between loggers and between tag versions using two ANOVAs.

| Calibration protocols within the literature
To examine the awareness of the scientific community about potential for variability in accelerometer data that could be corrected by calibration, we searched the scientific literature from the past 3 years In the walking speed trials with people, the minimum and maximum differences in VeDBA between calibrated and uncalibrated tags for any one participant ranged between 0.37% and 5.04%.
Mean VeDBAs per participant across speeds showed that the difference between calibrated and uncalibrated tags could amount to 2.5% of the calibrated reading. Inspection of the measures undertaken to calibrate each tag (see above) showed that the percentage difference between the uncalibrated and calibrated was primarily due to the acceleration multiplicator (see above; Figure 3).

| Post hoc quantification of accelerometer inaccuracy
The comparison of stationary data recorded by the two tag types deployed on tropicbirds indicated that the vectorial sum was lower in the type 2 tag (Wilcoxon test: W = 98, p = 0.005, difference = 0.03 g; Figure 7). Standard deviations of the vectorial sum (type 1: 0.03; type 2: 0.05) however, indicate that errors are more variable within type 2.
We could not determine multipliers for the three acceleration channels to calibrate the data based on this approach, as the heave and surge channels did not cover the whole spectrum of their possible distribution (−1 to 1 g) while the tag was motionless.

| Calibration protocols within the literature
Of the 100 papers examined, only five mentioned any calibration protocol for accelerometers that might have led to the correction of at least one of the sources of errors mentioned above (although many were not explicit enough to be sure). No publication explicitly referred to all potential errors.

| DISCUSS ION
This work highlights that there is currently virtually no discussion of acceleration calibration within the scientific literature even though variation in acceleration measured by tags on flying birds (and presumably other animals engaged in any activity) can be due to; (i) differences in sensitivity (Table SI1) and calibration between sensors, and that, in any event, variation occurs due to (ii) the placement of the tag (or the sensor within the tag) as well as (iii) variation due to the animal itself. It is therefore normal to attribute all variation to the activity of the animal itself but the validity of doing this is critically dependent on the other two factors. Indeed, as our work with F I G U R E 4 (a) Plot of mean heave versus surge acceleration through time for a pigeon during an average wingbeat cycle derived from a lower back-(red) and an upper back-mounted tag (blue), both recording at 150 Hz. Each point corresponds to a mean value of acceleration calculated across all flights for a given percentage through the wingbeat, starting from the peak of acceleration of the downstroke (black point). The value of each point was smoothed over a window of 10 points (10%) to reduce noise. Regressions of the upper against lower tag acceleration for defined points throughout the wingbeat cycle show; (b) heave, (c) surge and (d) sway accelerations (note the changing axis scales). The regression between the two tags is represented in grey, and the y = x line is shown in red

F I G U R E 6
Relationship between the wingbeat frequency and heave amplitude of red-tailed tropicbirds during two field seasons. Birds were equipped with type 2 tags in season 1 (red) and type 1 tags in season 2 (blue). In season 2, tags were attached using one less strip of tape, which could reduce tag stability. Full lines represent the linear relationship between wingbeat frequency and amplitude and dashed lines the confidence intervals Gunner et al., 2021) and studies looking at animal effort over time and space (Duriez et al., 2018;Halsey et al., 2011). Errors due to sensor inaccuracy and differences in placement are most severe when axes are considered individually (e.g. deriving pitch from the surge axis). However, they are also relevant when all three orthogonal axes are considered, as inaccuracies in one axis can either be mitigated or compounded by inaccuracies in another (see Figure 3). Within vectorial (or absolute) sums of acceleration metrics, the overall error will depend on the relative errors of the different axes and the extent to which they vary during the activity in question. For example, in flapping birds or bats, almost all variation in acceleration measures occur in the heave and surge axes (e.g. Wilson et al., 2008, and see

| Calibrations
The issue of inaccurate sensors can be at least partially mitigated by the 6-O method suggested in this work, although we note that this only effectively calibrates between −1 and 1 g, while the gravitational component experienced by some animals, for example, during turning (Wilson et al., 2013), will increase beyond these limits.
Although, ideally, the tags should be calibrated with each of the accelerometer axes held perfectly vertically (something that is challenging to do once a circuit board is potted in a housing), in practice, this is not critical, and holding the axes as close to vertical as possible should suffice. This is because the response of an accelerometer to the static acceleration of the earth's gravity follows a sine wave so that an accelerometer that is placed 10° off the vertical (i.e. at 80°), reads a value that is 98.5% of the full-scale value that would be given if the accelerometer axis were held perfectly vertical (so that if there is an error in this axis, 98.5% of it will be covered by this orientation). If it is impossible to reliably estimate the angle of the logger because of the housing, for instance, gently rotating the logger around in every direction would be needed to cover all six orientations, although this process is particularly sensitive to centripetal acceleration, which is added to the static signal, so the rotation speed must be very slow. Using this calibration will therefore allow researchers to ascribe the most substantive variation in acceleration signal to specific axes.
Our suggestion of dealing with errors post hoc by looking at the vectorial sum of the acceleration when tags were stationary could not be used to correct the various axes in our study because all six orientations required for the calibrations were not known, and the study subjects did not adopt the appropriate postures. However, this process does at least serve to indicate some of the extent of deviation of the sensors from the expected range (see Figure 5). In this regard, we note that we have presented results in this work from only one tag manufacturer (type 1 and type 2 tags use two different chips; the type 1 is far superior having a sensitivity of 0.061 mg [in a range of ±2 g], while the type 2 only has a sensitivity of 1 mg for this range), but we have measured, in passing, more substantive variation by other manufacturers (see Table SI1).

| Why does accelerometer position affect acceleration?
The position of an accelerometer on an animal should affect the acceleration perceived by the sensor during movement according to its location, and indeed that is the basis behind many biomechanical studies (e.g. Giansanti et al., 2003;Hyde et al., 2008). However, there is poor appreciation in the behavioural ecology community that this premise is also valid for trunk-mounted tags. This may seem irrelevant for birds where the thorax can be considered a single immobile unit, in contrast to bead-string models that may indicate what is expected in species with a flexible back (Underhill & Doyle, 2006).
Our work has shown, however, that the location of trunk-mounted accelerometers on birds does play a role in modulating acceleration values ( Figure 4) and this is presumably because the bird body pitches during the wingbeat cycle (although part of the differences that we observed may also be due to the movement of the scapulae and perhaps the neck during flapping). Depending on the degree of pitch, the centre of pitch rotation and the position of the accelerometer, this will change the extent of movement (d), which can be defined by the length of a section of a circumference around the F I G U R E 7 Comparison of the vectorial sum of the raw acceleration recorded by various immobile type 1 (dark boxes) and type 2 tags (light boxes). Each point corresponds to a different unknown orientation. Thick black lines indicate the median vectorial sum for each tag, extremes of the box the upper and lower quartiles, and whiskers the extreme values (excluding outliers) centre point of rotation according to D = 2πr(360/P), where r is the radius or distance between the centre of pitch rotation and the sensor, and P is the maximum pitch angle (in degrees). The duration of the wingbeat cycle will define the vertical speed of the tag at its location, with the recorded acceleration being the change in speed over time. The formula shows how the effect of changed acceleration will be more prominent with increasing distance of a tag from the centre point of rotation and so will have the greatest potential to vary in larger birds, all other things being equal. This may also account for the changed acceleration metrics in tail-versus bodymounted tags (Figure 5c,f) in our kittiwake study, although part of that is presumably due to the relative instability of the tail. In fact, to our knowledge, there is little information on the extent of bird body change in pitch during flight (but see Su et al., 2012;Tobalske & Dial, 1996) although controlled experiments with multiple calibrated accelerometers could change that. In the meantime, we suggest that users attempt to place accelerometers in identical positions on their study animals for comparative purposes, which should also involve knowing the position of the sensors within the tags rather than just considering the tags themselves (Figures 1 and 3).
Fortunately, there is no a priori reason why tags placed differently on a bird thorax or inaccurate accelerometers should affect determination of wingbeat frequency since points of inflection will still be represented correctly with respect to time within the wingbeat cycle (Figure 4a,b). Indeed, this is what we observed in our controlled pigeon flight trials and in the kittiwakes (despite a small difference in tag mass, see Whelan et al., 2021). In contrast, the tropicbird work indicates that there was a real change in wingbeat frequency across the two seasons, and this seems to be related to changes in environmental conditions (Garde et al., in prep).

| Post hoc studies and differences between tags
The bigger question is the extent to which observed differences in uncalibrated accelerometers can be attributed to the animals rather than to tag position, attachment techniques or sensor variability. In our tropicbird example, the differences in VeDBA and signal amplitude were not consistent with the differences found in pigeons, where higher values were recorded in the upper tag. This suggests that the variation in signal amplitude in tropicbirds was not related to tag position. Furthermore, the difference in amplitude was appreciably larger between the two tag types on tropicbirds, than between the upper and lower tags used in pigeons, even though the tropicbird tags were placed in a way that minimised the distance between their respective accelerometers. The scale of the variability is not consistent with that caused by uncalibrated sensors, as the difference between vectorial sum values in 6-O calibrated tags and uncalibrated tags (in general) amounted to a mean maximum of 2.5%. In contrast, in flapping flight, the difference in VeDBA between tags and seasons reached 25%. This order of magnitude difference might appear to indicate seasonal changes in flight effort. However, this also appears unlikely, as higher signal amplitudes were recorded in the season with lower wingbeat frequencies, despite the fact that these parameters are positively correlated within each season ( Figure 6).
It therefore appears that the factors driving seasonal differences in signal amplitude are different to those driving seasonal changes in wingbeat frequency.
The difference in signal amplitude may also arise due to changes in the stability of the tag attachment between seasons. Wilson et al. (2021) note how accelerometers in loosely fitted collars on terrestrial mammals provide a signal that varies with collar tightness. Although the use of tape to attach devices to birds (Wilson et al., 1997) provides a much more intimate association between the tag and the bird body, we believe that if this method is not standardised (and it was not in our study, as the amount of tape varied between seasons), it can lead to major variation in acceleration values, particularly in animals with highly dynamic movement, such as flight. In birds, this issue may be exacerbated by tag movement due to air flow over the body which can cause the device to vibrate more or less depending on attachment (cf. Wilson et al., 2020). It is also germane to consider that the stability of the tag attachment may change over time in longer-term deployments. These issues have long been recognised in the wearable sensors industry for humans (Jayasinghe et al., 2019). Consequently, we cannot, in good faith, compare VeDBA or wingbeat amplitudes of tropicbirds between seasons, although the wingbeat frequency will be unaffected by the attachment procedure, tag position or sensor inaccuracies.

| CON CLUS IONS
Accelerometer inaccuracies can result in errors in the raw acceleration of up to 5% per axis and, depending on the extent and direction of the errors across all three orthogonal axes, this can affect DBA metrics accordingly. Tag placement can also result in errors in DBA metrics of up to 9.7% in flapping flight for our units, although we note that the scale of the errors varies between device types. Finally, non-standardised tag attachment procedures can result in highly variable dynamic acceleration values. Taken together, these represent a potentially important source of error in both raw acceleration values, which are commonly used to calculate body pitch and roll and/or as parameters to define particular behaviours, and derived metrics such as DBA. Attachment procedures should be adapted to the species tagged, as the effect of different tag placements may vary from one species to the other (e.g. Kölzsch et al., 2016;Vandenabeele et al., 2014), and to the study, as different metrics may be measured more reliably using one particular method (Kölzsch et al., 2016), making the use of a standardised procedure difficult.
Animal disturbance and study purposes should be considered before adjusting tag placement for the compatibility of datasets, and therefore, researchers should be aware of the attachment methods used to compare acceleration metrics between studies reliably (Sequeira et al., 2021). Importantly, we highlight that sensor inaccuracy can be largely mitigated by performing a rapid calibration. There is therefore a need for researchers to undertake such calibrations prior to each deployment and include this in their archived data as well as to standardise their tag attachment procedure as much as possible.
The last decade has been hailed as a golden age in biologging, due to the availability of powerful sensors in animal-attached technologies.
The data repositories that archive these data represent extremely valuable resources for the community (e.g. Davidson et al., 2020), but there is an urgent need for calibrations that allow data to be standardised in order for their full potential to be realised now and in the years to come.

ACK N OWLED G EM ENTS
Special thanks to Jenna Schlener and Charlotte Rees-Roderick for their contribution to the kittiwake and the wind tunnel studies, respectively, as well as to the participants of the walking experiment.
We are grateful to the National Parks and Conservation Service,

Government of Mauritius, who provided permission to access Round
Island to tag red-tailed tropicbirds. This work was funded by the European Research Council starter grant 715874 to ELCS, under the European Union's Horizon 2020 research and innovation program.

CO N FLI C T O F I NTE R E S T
We declare we have no competing interests.

AUTH O R S ' CO NTR I B UTI O N S
Red-tailed tropicbird data were collected by A.F., N.C. and V.T.; All authors contributed to the revision of the manuscript, gave final approval for publication and agree to be held accountable for the work performed therein.

PEER R E V I E W
The peer review history for this article is available at https://publo ns.com/publo n/10.1111/2041-210X.13804.

DATA AVA I L A B I L I T Y S TAT E M E N T
Data and code used for the analyses of this manuscript are available from the Dryad Digital Repository https://datad ryad.org/stash/ datas et/doi:10.5061/dryad.f7m0c fxwj (Garde et al., 2022).